Hot Tub Site Preparation & Installation

Hot Tub Site Preparation and Installation

Please consider the following hot tub site preparation and installation notes before you order your tub.  If you think that you might need a crane to get your tub into position then please contact us to discuss the situation before you order.

Hot Tub Base

Positioning

Access to Site

Electrical Supply

Safety Considerations

Water Supply

Hot Tub Base

Your hot tub needs a good solid foundation. A hot tub filled with water and people is heavy. The area that your hot tub sits on must be able to support the weight of the tub, the water in it and those who use it. A concrete base should be at least 4” thick. If you are installing your hot tub on an elevated wood deck or other structure, it is advisable to consult a structural engineer to ensure that the structure will support the weight.

If the foundation is inadequate, it may shift or settle after the hot tub is in place, causing stress to the shell.  Damage caused by inadequate or improper foundation support is not covered by any hot tub warranty and it is the responsibility of the hot tub owner to provide a proper foundation for the hot tub.

If you are installing your hot tub indoors choose flooring that won’t be damaged by water.

back to top

Positioning

Some things to consider when positioning your spa include:

Is it close to where you are going to get changed? A long chilly walk to the tub might be a bit off-putting!

Is it safe for young children? Can you see what they are up to?

Is it overlooked? You might not feel able to relax if you feel conscious of the fact that your neighbours might be watching.

Is it under overhanging trees? The last thing you want is loads of greenery decaying in your water.

Is there a clean path from the changing area to the tub? Grass and debris from the users' feet will get transferred into the water.

Is it sheltered from the wind?

Is there a pleasant view?

is there a slope on the base?  If so, remember that one side of your tub will have deeper water in it that the other.  Also, think about placing the hot tub so that water drains away from the side of the spa where the electrical components are located, thus ensuring that there is no risk of water damage.

It is a good idea to outline the hot tub's proposed location using a garden hose or rope. This will help you visualise your plan for the area

back to top

Access to Site

Check the dimensions of your hot tub and compare them to the width of any gates and paths along the delivery route between the road and the installation site. It may be necessary for you to remove a gate or partially remove a fence in order to provide an unobstructed passageway. 

If the delivery route will require a 90° turn, don’t forget to check the measurements at the turn to ensure the hot tub will fit.  Also, look for any protruding utility meters, low roof eaves, overhanging trees or gutters that might cause an obstruction.

Stairs can cause a problem, depending on the weight of the tub.  In some circumstances it might be necessary to hire a crane for the installation.  This could be to avoid damage to the tub or to your property, or simply because there is no other way to get the tub into position.  If you think this is necessary don't panic.  Hire of a crane is not as expensive as you might think and there is usually a choice of local firms able to give you a quotation.

Electrical Supply

Depending on the model chosen, the power requirements are likely to be be either 13 amp or 30 amp single phase.  A qualified electrician must install the power supply, which must be wired through a Residual Current Device (RCD), or circuit breaker, at least 2 metres away from the hot tub. All outside cable should be armoured. 

Hot tubs rated at 13 amps may be connected via a standard, switchable, waterproof 3 pin socket.  Hot tubs rated at 30 amps will need to be wired directly into a waterproof (IP55 or above), switchable junction box.

back to top

Safety Considerations

Do not place your hot tub within 3 metres of overhead power lines. Make sure your hot tub is positioned so that access to the equipment compartment and side panels will not be blocked.

back to top

Water Supply

There must be a non-softened water supply and hosepipe within reach in order to fill the tub.

An accessible drain in which to direct the water when emptying the tub is also useful.

back to top