HOT
TUB COVER LIFTERS - SIDE MOUNT
Cover lifters avoid wear and tear to your spa cover.
If you don't want to screw into the side of you spa consider an
under-mount cover lifter.
This very economical cover lifter from Cover Valet in the
USA will attach to either a wooden or plastic sided spa.
The Cover Genie is an innovatively designed,
low-profile lifter that will fit most spa covers. Only
about 12" of clearance behind the spa is needed. This cover
lifter is well constructed of the highest quality materials
and powder coated.
Requires only approximately 3" (760mm) of
side clearance.
Cover Genie installation instructions
£
The Cover Rock-It is well constructed of the
highest quality materials and powder coated aluminium. It
installs easily in minutes and is an very affordable solution
from Cover Valet in the USA. This cover lifter attaches to
the skirt of your spa and stores the cover at ground level.
The Cover Rock-It Side Mount fits most spas up
to 96" (2.4m) wide, but we recommend it's use for smaller
(under 1.5m width) spas.
Requires only approximately 3" (760mm) of
side clearance.
Cover Rock-It Installation Instructions
£
NB: his cover lifter is also available with a slip under the
spa mount system to avoid drilling into the spa skirt.
A basic 'frame' type lifter that stows the cover to one side and low against the spa.
It is held in place by 2 brackets, at floor level, at the back of the spa.
When opened, the cover is then held in place with 2 nylon,
UV-resistant retaining straps fixed at each spa side.
Now supplied with the TowelMate accessory for hanging up to three
towels right where they're needed most.
Made of black powder-coated aluminium with screw caps, and rubber grips.
Made of larger size aluminium tubing to virtually eliminate twisting and
torquing and is therefore recommended for medium to large size spas (over
1.5m width) spas.
CoverMate
Easy Installation Instructions
£
The
No 1 cover lifter in the industry.
Made from aluminium with composite brackets for complete corrosion free
operation.
This is a side mounted lifter to stow the cover to one side and above the
spa. It is now supplied with the TowelMate accessory for hanging up to three
towels right where they're needed most.
CoverMate
I Installation Instructions
£
The
Covermate II is a good choice of cover lift when clearance behind the spa is
not important (18"/46cm clearance is needed). The cover is stored low
down but off the ground.
Made of black powder-coated aluminum with screw caps, bolt covers and
rubber grips to ensure years of trouble-free performance.
Fits most spas up to 96" (2.4m) wide.
£
CoverMate
II Installation Instructions
NB: his cover lifter is also available with a slip under the
spa mount system to avoid drilling into the spa skirt.
This
unique sliding action lifter from Cover Valet provide
effortless cover removal.
This spa cover lifter works by simply
sliding and then dropping the spa cover conveniently to the
back side of the spa.
Just 10-12" clearance is needed behind the spa.
The Cover Slide-It is constructed from zinc plated, black,
powder-coated steel and is built to withstand harsh
environments. Two heavy duty zinc plated steel brackets are
attached to the spa cabinet.
Cover
Valet Slide-It Installation Instructions
£
This cover lifter is British made from 100% light
weight aluminium so it won't rust. They feature 3mm wall
thickness tubing which gives a strong, rigid construction.
[Check out any cheaper brands carefully because they're very
likely to be only 1.5mm wall thickness, providing poor rigidity
and little protection from bending in strong winds or when using
with larger spa covers.]
Nylon powder coated for extra toughness and
supplied with high tensile bolts to fix to your spa.
Complete with comprehensive fixing instructions and
appropriate size drill bit. All you have to do is
supply the tools!
The
cover does not touch the floor during operation of the lifter.
Fits any square or oblong hot tub up to 8 ft (2.45 m) wide.
EasyLift 1
Installation Instructions
£
Rear clearance required: thickness of the folded
cover approximately 18” (440mm).
Side clearance required: 4" (100mm)
NB: his cover lifter is also available with a slip under the
spa mount system to avoid drilling into the spa skirt
The
Cover Valet is the worlds best
premium cover lifter.
This low profile spa cover lift
works where others can't! The Cover Valet lifts and stores
covers on spas set inside gazebos, those sunken in a deck or
in any tight space. I
ts versatility allows for use
with a wide range of spa installations, and it is
particularly handy when space is limited. Just 6-8"
clearance is needed behind the spa and the Cover Valet fits
any width spa cover.
Dual gas springs assist in
effortlessly lifting and lowering the cover.
A locking feature holds the
cover open until you are ready to close it.
The Cover Valet is constructed from zinc and powder coated
stainless steel and is built to to stand up to harsh
environments. Two heavy duty zinc coated metal frames are
attached to your spa cabinet or the decking next to your in
ground spa.
The Cover Valet makes it possible for
absolutely anybody to lift a heavy spa cover.
The Cover Valet has a one year warranty and
the pneumatic pistons are replaceable, should that ever be
required.
Cover Valet installation instructions
Spa Covers
up to 90" / 2.29m - £
Spa Covers over 90"/ 2.29m
- £
Cover Valet
Cover Caddy
The
Cover Caddy from Cover Valet in
the USA gives you a hand with
your spa cover with just three simple steps:
1) Raise and open support arms.
2) Fold the spa cover in half and slide onto
support arms.
3) Push the spa cover downward into a stored
position.
Gas spring assistance allows the cover to be
easily pushed down and replaced. The Cover Caddy™ comes
fully assembled in the box for ease of installation.
The Cover Caddy has a one year warranty and
the pistons are replaceable, should that ever be required.
Cover Caddy Installation Instructions
£
This cover lift is
designed specifically for round and octagonal spas, but will
also fit square or oblong hot tubs up to 8 ft (2.44 m). It
is pneumatically assisted and is and when in the open
position, the
Cover
Ease positions the cover well away from the hot tub so that
your use is not restricted in any way.
The mounting base system enables the CoverMate FreeStyle to be installed on virtually any hot tub.
The adjustable mounting base system simply
slides under the hot tub. The spa's weight provides a
massive amount of strength to support the bracket system.
£
CoverMate Freestyle assembly instructions
Rear clearance required: 12"
Side clearance required: None
Back
Leisure Concepts
Leisure
Concepts 
About Us
| What our Customers Say |
Terms & Conditions |
Site Map |
Links | Hot Tubs | Splash Spas Trade